Production of boilers in Czech Republic has centuries-old history. The first steam boiler was made in 1824. During this time began a long and varied history of manufacturing various power equipment. Various types of boilers have been developed from simple original equipment. Three thousand boilers were constructed in the early 20th century in Czech Republic. The tradition of production and technical skills is passed from generation to generation over past 186 years.

BPP Energy company continues the long tradition in boiler and power equipment production in Brno. This modern and dynamic company was founded in 2011 and mainly focuses on the production of BOILER PRESSURE PARTS.

The production headquarters is in Zakrany, whis is approximately 15 km far from Brno, Czech Republic, where the head office is located. Workshop area has more than 4000 square meters.

We supply membrane walls, coils, super heaters, reheaters and economizers.

Our vision is to become successful and well accepted international company. We would like to be a key partner for our customers by providing high quality services and timeless solutions.

Our values are quality, accountability and teamwork.

CERTIFICATES AND STANDARDS

• EN ISO 9001 (PDF)
• EN ISO 3834-2 (PDF)
• ASME “S” (PDF), ASME “U” (PDF) we are in certification process.
• EN 12952 + PED 2014/68/EU

QUALITY POLITICS

• Quality Politics (PDF)

MAINTENANCE AND REPAIR SERVICE FOR POWER GENERATION INDUSTRY

• Coal boilers
• Boilers for municipal waste incineration
• Biomass boilers
• Combined cycle boilers
• Agricultural waste fired power plant
• Process Recovery Boilers
• Gasification Boilers

MANUFACTURING AND MAINTENANCE

• Water Wall Panels
• Superheaters
• Reheaters
• Economizers
• Air Heaters
• Steam-air Preheaters
• Air, Flue Gas Ducts
• Coils

REPAIR AND MAINTENANCE

• Valves
• Motors
• Conveyors
• Pumps, etc.

SEMI AUTOMATIC WELDING LINE “PEMA”

Manufacturer: PEMA

Technical data

• Minimal thickness of tubes (wall thickness): not less than 4 mm
• Maximal width of welded panels: 1900 mm
• Maximal length of welded panels depends on course, on which panels outweigh

The average daily capacity

• 1 shift: 300 m of weld
• 2 shifts: 650 m of weld
• 3 shifts: 900–1000 m of weld

PANEL BENDER “W001”

Manufacturer: WEGAR

Technical data

• It can bend from diameter of tube 28 mm to diameter 108 mm
• Maximal width of bended panels: 1600 mm
• Range of bends: 3°–130°

AIR BLAST MACHINE OF TUBES “2 TP 110”

Manufacturer: Slavata-Praha

Technical data

• Air blast machine can work in local and automatic control
• By settings is possible to change abrasive flow
• Minimum diameter of blasted pipe: 25 mm
• Maximal diameter of blasted pipe: 100 mm
• Conveyor speed during blasting: 4–6 m/min
• Quantity of projectile units: 2
• Blasting agent: steel granulate

PLANER OF PLATES “HHP 12”

Manufacturer: TOS Hulín

Technical data

• Dimensions of machine: 14 200 mm
• Maximal length of machining: 12 000 mm
• Maximal machined thickness of plate: 80 mm
• Quantity of pressure pistons: 21
• Planer of plates is equipped with mobile control workplace

BENDING MACHINE “H 108–CLIMAX”

Manufacturer: PBS Brno

Technical data

• Minimal wall thickness of bended tubes: 4 mm
• Maximal wall thickness of bended tubes: 10–16 mm (in tubes diameter 102 and 108 max. wall thickness 10 mm)
• Maximal length of bended tube: 10–15 mm
• Bends range: 3°–180°
• Minimal radius of bended tubes: 1,8 D (tube diameter)
• Bending is performed on spindle
• Maximal length of tube–putting on spindle: 7 m

CNC BENDING MACHINE “AMOB CH 120”

Technical data

• Max capacity steel 114,3 x 8,6
• Max capacity stainless steel 118,0 x 2,0
• Max section modules 70, 24
• Minimum CLR/D 1 x D
• Max centered radius of bend (mm) 425
• Machine length with spindle (mm) 6000
• Max length of tube for bend without spindle (mm) – unlimited

FINS CALIBRATION AND BLASTING

Technical data

• fins calibration
• fins cutting
• fins blasting